Data visualization with SAS programming

How to get rid of legend of reg fit plot using SAS 9.4 ODS graphics editor?

Accepted Solution Solved
Reply
Frequent Contributor
Posts: 82
Accepted Solution

How to get rid of legend of reg fit plot using SAS 9.4 ODS graphics editor?

Dear All,

I made a fit plot graph  with attached file using SAS 9.4, the program is below:

ods listing sge = on;

procreg data=baseline2;

model ba=bs;

run;

I don't want legends especially 'observation, parameters, error DF, etc'.

I appreciate your help.

Thanks,

Xinjian

Attachment

Accepted Solutions
Solution
‎10-29-2014 05:33 PM
SAS Super FREQ
Posts: 1,044

Re: How to get rid of legend of reg fit plot using SAS 9.4 ODS graphics editor?

There is no way to remove a Legend or the Statistics table from a graph using the ODS Graphics Editor.  However, you could use the following code to get the data from proc REG and plot it using SGPLOT.

ods output fitplot=fitdata;

proc reg data=sashelp.class;

model weight=height;

run;

proc sort data=fitdata out=sorted;

by _indepvar1;

run;

ods graphics / reset width=6in height=4in imagename='ClassWeightbyHeightFitPlot';

proc sgplot data=sorted nocycleattrs noautolegend;

  band x=_indepvar1 upper=uppercl lower=lowercl / nofill lineattrs=(pattern=dash);

  band x=_indepvar1 upper=upperclmean lower=lowerclmean;

  reg x=_indepvar1 y=predictedvalue / nomarkers;

  scatter x=_indepvar1 y=depvar;

run;

For a simple fit plot, it would be even easier to just use the REG statement inside proc SGPLOT:

ods graphics / reset width=6in height=4in imagename='ClassFitPlot';

proc sgplot data=sashelp.class nocycleattrs noautolegend;

  reg x=height y=weight / cli clm;

run;

View solution in original post


All Replies
Solution
‎10-29-2014 05:33 PM
SAS Super FREQ
Posts: 1,044

Re: How to get rid of legend of reg fit plot using SAS 9.4 ODS graphics editor?

There is no way to remove a Legend or the Statistics table from a graph using the ODS Graphics Editor.  However, you could use the following code to get the data from proc REG and plot it using SGPLOT.

ods output fitplot=fitdata;

proc reg data=sashelp.class;

model weight=height;

run;

proc sort data=fitdata out=sorted;

by _indepvar1;

run;

ods graphics / reset width=6in height=4in imagename='ClassWeightbyHeightFitPlot';

proc sgplot data=sorted nocycleattrs noautolegend;

  band x=_indepvar1 upper=uppercl lower=lowercl / nofill lineattrs=(pattern=dash);

  band x=_indepvar1 upper=upperclmean lower=lowerclmean;

  reg x=_indepvar1 y=predictedvalue / nomarkers;

  scatter x=_indepvar1 y=depvar;

run;

For a simple fit plot, it would be even easier to just use the REG statement inside proc SGPLOT:

ods graphics / reset width=6in height=4in imagename='ClassFitPlot';

proc sgplot data=sashelp.class nocycleattrs noautolegend;

  reg x=height y=weight / cli clm;

run;

Frequent Contributor
Posts: 82

Re: How to get rid of legend of reg fit plot using SAS 9.4 ODS graphics editor?

It is good to know ods graphic editor cannot change legend. I tried your way to get job done. Thanks so much for your effort.

Post a Question
Discussion Stats
  • 2 replies
  • 347 views
  • 0 likes
  • 2 in conversation