BookmarkSubscribeRSS Feed
paulbr
Calcite | Level 5

Dear community,

I'm trying to color the gap between two series charts depending on which of the two y-values is greater.

I colored an example plot in MS Paint, to visualize the idea.

So far I've tried various options in the band statement, but failed. My hope was that the band plot would vanish when the lower values is greater than the upper value. Then I could use two band plots, each with a different filling color. But also that does not work.

Do you have any idea how I could get such a chart in SAS?

Thanks a lot,

Paul

Ex2.png

data temp;
input x y1 y2;
datalines;
1 50 70
2 60 65
3 70 50
4 60 100
;;
run;

proc sgplot data=temp;
series x=x y=y1;
series x=x y=y2;
run;

5 REPLIES 5
RW9
Diamond | Level 26 RW9
Diamond | Level 26

Hi,

 

I would probably go down the route of a polygon plot:

http://blogs.sas.com/content/graphicallyspeaking/?s=polygon

 

You can draw each polygon with its own color.

DanH_sas
SAS Super FREQ

I've actually done something like this before. In my paper, "Secrets of the SG Procedures", I did this plot of a sine wave:

 

%let THRESHOLD = 0;
data wave;
do x=-6 to 6 by .05;
y=sin(x);
if (y >= &THRESHOLD) then do;
positive = y;
negative = &THRESHOLD;
end;
else do;
positive = &THRESHOLD;
negative = y;
end;
output;
end;
run;


proc sgplot data=wave noautolegend;
   yaxis grid label="y";
   xaxis grid;
   band x=x lower=&THRESHOLD
            upper=positive / transparency=0.5;
   band x=x lower=negative
            upper=&THRESHOLD /
            transparency=0.5;
run;

 

The key to this example is the data manipulation. In a BAND plot, if the upper and lower values are the same, then NOTHING is drawn in that segment. What's trickier about your example is that the y1/y2 invert in places where there is no data. You would need to do some extra work to put data values at those locations.

 

Hope this helps!

Dan

Jay54
Meteorite | Level 14

RW9's proposal to use POLYGON will work, but you will need to compute the intersection of the two lines, which may not occur at exact axis value.  A partial result is obtained by using one band to wrap back over itself as shown below.  You will get the correct filled area.  But, now we need to figure out how to color each area differently. 🙂

 

data temp;
input x y;
datalines;
1 50
2 60
3 70
4 60
4 100
3 50
2 65
1 70
;
run;

proc sgplot data=temp;
band x=x upper=y lower=0;
run;

 

Band.png

Rae_
Fluorite | Level 6

I am doing something similar for a consort diagram and needing to have boxes that are shaded differently.  I discovered that if I created two xy sets then I could label them individually.  Not sure if that would work for you here but since I found this while looking for a solution I thought I would include it. 

 

data final;
set box ;
if subnode in (1,3) then do; x_yellow=xb; y_yellow=yb;end; 
if subnode in (2) then do; x_maize=xb; y_maize=yb;end; 
run;

 

ods graphics / reset width=8.5in height=24in noborder;
proc sgplot data=final noborder noautolegend;
polygon id=box  x=x_yellow y=y_yellow/ fill fillattrs=(color=CxFFC000) outline;
polygon id=box  x=x_maize y=y_maize/ fill fillattrs=(color=CxBF9000) outline;
run;

 

DanH_sas
SAS Super FREQ

I've done something similar to this with band plot. Take a look at page 2 of https://support.sas.com/resources/papers/proceedings09/324-2009.pdf

 

Hope this helps!

Dan

sas-innovate-2024.png

Join us for SAS Innovate April 16-19 at the Aria in Las Vegas. Bring the team and save big with our group pricing for a limited time only.

Pre-conference courses and tutorials are filling up fast and are always a sellout. Register today to reserve your seat.

 

Register now!

How to Concatenate Values

Learn how use the CAT functions in SAS to join values from multiple variables into a single value.

Find more tutorials on the SAS Users YouTube channel.

Click image to register for webinarClick image to register for webinar

Classroom Training Available!

Select SAS Training centers are offering in-person courses. View upcoming courses for:

View all other training opportunities.

Discussion stats
  • 5 replies
  • 1317 views
  • 0 likes
  • 5 in conversation